Water Tests
Here you will find everything you need to measure the water values in your koi pond yourself: JBL drop test kits for pH, KH, GH, ammonium, nitrite, nitrate, phosphate and oxygen, matching reagent refills and spare parts, electronic meters for pH, oxygen and salt content, and a floating stainless steel pond thermometer.
For weekly routine checks, a test kit covering the key parameters is enough. If you measure frequently, salt your pond or want to monitor oxygen precisely, add an electronic meter. Products for correcting the values can be found under .
Frequently Asked Questions
Which water values should I test regularly in a koi pond?
For an established pond with normal stocking, we recommend measuring pH, KH, ammonium/ammonia, nitrite and oxygen at least once a week. With high stocking, after alterations or when problems arise, you should test more often. Nitrate, phosphate and total hardness complete the picture, for example with algae problems or after larger water changes.
Drop test or electronic meter: which is better?
Drop tests work by colour comparison, cover many parameters and need no calibration, but the reagents have an expiry date. Electronic meters display an exact numerical value but must be calibrated regularly, and their electrodes are wear parts. For salt content, an electronic meter is the practical solution.
Which values are considered good in a koi pond?
Guideline values are a stable pH between 6.5 and 8.5, a KH of 5 to 10 °dH and more than 6 mg/l oxygen. Ammonium and nitrite should be practically zero in an established pond. For nitrate, manufacturers state below 50 mg/l, while veterinary recommendations for koi tend to be below 20 mg/l.
Can I use my municipality’s water hardness figure?
Only to a limited extent. Swiss water suppliers state total hardness in French degrees (°fH), while most pond tests measure in German degrees (°dH): 1 °dH corresponds to about 1.8 °fH. Carbonate hardness (KH), which is decisive for the pond, is usually only part of the total hardness and should therefore be measured separately.
Why water tests are essential in a koi pond
Clear water says little about its quality. Ammonium, nitrite or an unstable pH are invisible and are often only noticed once the koi already show unusual behaviour. A water test reveals such developments early, for example when the filter biology is not yet fully working after cleaning, in a new pond or in spring, or when too much food is given.
For a well-functioning pond with normal stocking, we recommend measuring the key parameters at least once a week. Record the values in a measurement log: only the trend over several weeks shows whether a value is slowly deteriorating.
The key water values and their guideline ranges
The pH should remain stable between about 6.5 and 8.5. Rapid fluctuations are more dangerous than a value slightly outside this range. Carbonate hardness (KH) buffers the pH and should be at least 5 °dH, with 5 to 10 °dH as the guideline. Ammonium/ammonia and nitrite are produced when waste and leftover food break down. In an established pond with a working biofilter, both should be practically zero.
Nitrate is the end product of this breakdown and accumulates without water changes. Manufacturers state below 50 mg/l for ponds, while veterinary recommendations for koi tend to be below 20 mg/l, partly because nitrate promotes algae. For oxygen, more than 6 mg/l is considered good. Phosphate should stay below 1 mg/l, and total hardness (GH) is ideally between 6 and 16 °dH.
Ammonium and ammonia: why pH makes the difference
Ammonium (NH4) and ammonia (NH3) exist in equilibrium in water. It is mainly ammonia that is toxic to fish, and its share depends strongly on pH and temperature. At 20 °C it is around 0.4 % at pH 7, around 4 % at pH 8 and already around 28 % at pH 9. The same ammonium reading is therefore about seven times more critical at pH 9 than at pH 8.
That is why ammonium should never be assessed on its own, but always together with pH and water temperature. The JBL ammonium test records ammonium and ammonia together and is evaluated using a colour chart and table. You then estimate the toxic share from pH and temperature.
KH and pH: the buffer in pond water
During the day, algae and plants consume carbon dioxide through photosynthesis, while at night all living things in the pond release it. As a result, the pH rises during the day and falls again at night. Sufficient KH dampens these fluctuations. If it drops below about 5 °dH, the pH can swing sharply and quickly.
Therefore always measure pH and KH at roughly the same time of day so that your values remain comparable. With the JBL Kombiset Plus NH4, the carbon dioxide content can also be derived from KH and pH using a table.
Drop test kit or electronic meter
The compact JBL Kombiset Plus NH4 covers pH, KH, ammonium, nitrite and nitrate and is suitable for routine checks. The JBL Wassertest Lab Koi additionally contains tests for GH, phosphate and oxygen, a second pH range from 7.4 to 9.0 for more precise measurements in the alkaline range, and a thermometer. Empty or expired reagents can be bought individually, as can cuvettes, syringes and measuring spoons.
Electronic meters deliver an exact numerical value within seconds. The Duo Tester measures pH and temperature, and we also stock pH 7.00 calibration solution for electronic pH testers. The electrodes of such devices are wear parts. The Greisinger G1610 measures dissolved oxygen from 0 to 20 mg/l as well as temperature. The KoiMedic salt meter measures salt content from 0.00 to 1.00 % with an accuracy of 0.01 %.
Measuring oxygen and salt in a targeted way
Oxygen content is lowest at night and early in the morning because no photosynthesis takes place then. A morning measurement therefore shows the critical low point. In addition, warm water dissolves less oxygen than cold water, so the value becomes tighter in summer. If readings are regularly low, it is worth looking at .
If you salt your pond, measuring is unavoidable: every water change dilutes the salt, and without a reading the top-up dose cannot be determined. Veterinary sources give 0.1 to 0.3 % salt as the range that protects koi against nitrite uptake through the gills. Check your salt meter at least once a year with 0.5 % calibration solution.
Swiss tap water and water hardness
Tap water hardness in Switzerland varies greatly from one municipality to another because it depends on the rock layers the water flows through. Your water supplier or trinkwasser.ch states the total hardness for your municipality in French degrees (°fH). To convert to the German degrees used by most pond tests, divide the value by 1.8: 27 °fH therefore corresponds to about 15 °dH.
However, total hardness does not reveal how high the carbonate hardness is, which is decisive for pH stability in the pond. Measure KH yourself, ideally both in the pond and in the tap water you use for water changes.
From reading to action
With drop tests, follow the sample volume, order of reagents and waiting time exactly, otherwise the colour will be distorted. Measure again after a partial water change to check the effect. If ammonium or nitrite rise, a partial water change, less food and a check of the are the first steps. Products for raising KH or stabilising the water can be found in the category.